So, you have purchased a device to increase the odometer readings via the CAN bus for your make and model of car. To use the device correctly you must:
If you have a domestic car or a foreign car produced before 2006, then you need a different speedometer winding. This category of cars is equipped with a speed generator that operates through a standard speed sensor and is connected to the cigarette lighter in the passenger compartment.
Our device is extremely simple to use. You turn the key or press the ignition button, insert it into the diagnostic connector, usually located under the steering column in the car. Turn on the daily mileage to immediately see the result and watch the odometer, which begins to increase its readings. This electronic device cannot change mileage; its task is different. The speedometer speedometer depends on your make and model of car, in most cases it is 1000 km/h, which, you see, is not bad! After the mileage meter shows what you need, remove the device from the connector and turn off the ignition. We do not recommend using the speedometer corrector while driving to avoid electronic errors.
The operating principle of our speedometer twister is as follows: the device operates via a digital CAN bus, sending a special signal to the circuit. Relatively speaking, this is the same signal that the car itself sends when driving. The speedometer control does not have additional power, but uses 12 volts of the car. As a rule, the CAN bus wires are routed to the diagnostic connector in the passenger compartment by the manufacturer, and they allow this device to operate. This tire is also actively used for diagnosing the technical condition of cars.
* The purpose of the device is to diagnose the operation of a car odometer and restore the true readings.
2009 - 2013
1. Description..................................... 3
....................................................................... 5
3. Description of the program ConfigCan. exe........................................................... 8
4. Winding programming ........................................................................ 9
5. Connection of winding .................................................................................. 15
6. Manual inputCAN– parcels......................................................................... 17
7. CANanalyzer (hacker) ................................................................................ 21
8. Limitation of winding operating time .................................................. 23
9. Other program functions ......................................................................... 25
10. Contact information .............................................................................. 26
The winding is designed to increase the speedometer readings through CAN tire The winder is connected through the vehicle's diagnostic connector. Rewinding does not affect the vehicle systems and does not cause errors.
The winder is universal and can be adjusted to different types of cars. Winding adjustment is done using a special program ConfigCan. exe . The appearance of the program is shown in Fig. 1. Using the program, you can configure the make of the car, as well as set the mileage limit.
Fig 1. Appearance of the program
The program only works with a special adapter. The appearance of the adapter is shown in Fig. 2. For the adapter to work correctly, you must install the driver.
Rice. 2. Appearance of the adapter for programming winding
2. Installing the adapter driver
1. Connect the adapter to your computer. Windows will prompt you to install the driver. Select the last item and click the “Next” button.
2. Select “Install from a specified location” and click “Next”.
3. Specify the folder where the driver is located and click “Next”.
4. Wait for the driver to install.
5. Click the "Done" button. This completes the driver installation.
3. Description of the program ConfigCan . exe
Rice. 1 Components of the program
The program consists of the following components:
1 – car type selection window;
2 – window displaying brief instructions for connecting the winder with
connection photo;
3 – setting mileage limit;
4 – record a new type of car;
5 – display of current winding settings;
6 – exchange management;
7 – serial number of the adapter.
To program winding for a specific vehicle, perform the following steps:
1. Disassemble the winder (unscrew the four screws).
2. Connect the winder to the adapter. When connecting, you must align the mark on the adapter connector and the mark on the board.
Rice. 3 Connecting the winder to the adapter for programming
3. Connect the adapter to your computer.
4. Run the program ConfigCAN. exe.
6. In the left window, select the car make.
7. Click on the plus sign to the left of the car brand and double-click on the specific model.
8. The car make should appear in the "Change car type to" line.
9. Click the Record button.
10. After a successful recording, the “Recording was successful” sign should appear.
11. Click the "OK" button.
12. This completes the winding programming.
13. Verify that the recording was successful. The values for “Vehicle Type” and “Change Vehicle Type To” must match.
14. This completes the winding programming. You can click on the “Exit” button
On most cars, connecting the winder involves installing it in the diagnostic connector, which is usually located under the steering column. On cars produced by companies Audi, VW, Skoda, BMW, Mercedes, Mitsubishi Insertion into the vehicle wiring is required. Instructions for installing winding on cars are built into the program.
To view the instructions for installing the winder, do the following:
1. Connect the winder to the adapter;
2. Connect the adapter to your computer and run the program ConfigCan. exe ;
3. Program the winding for the car you are interested in;
4. After this, the “Connection Method” window will display information on connecting the vehicle you have selected;
5. Click on the “Photo” button and a window with a photo of the connection will appear
Installation procedure:
1. Turn on the ignition or start the car
2. Install the winder into the diagnostic connector
3. After reaching the desired mileage, remove the winder
4. Turn off the ignition
6. Manual input CAN - parcels
The program has a function for manually entering parcels into the rewind. To switch to this mode, you need to click on the “Manual Entry” button.
Parcel setup:
1. The rewind supports the transmission of up to 16 parcels. To allow parcel transfer, you must check the box " Enable » opposite the corresponding parcel.
2. Winding supports standard and advanced ID . If the checkbox “29 bit » is installed, then the extended ID , if removed, then standard ID.
3. In the Delay window You must enter the time until the next shipment. If only one parcel is used, then this time will coincide with the period. If there are several parcels, they will be transmitted in a circle.
4. Rewinding supports different transmission speeds. You need to click on the arrow and select the desired speed.
5. The rewinding function implements the function of increasing data with a given step. To do this, you need to check the box next to the corresponding byte of the package (with D 0 to D 7) and enter the increment value in the box Value . The data increase occurs only for the first sending.
6. After entering all the data, you must click the “Record” button and wait for the window that the recording was successful.
7. After this, the car type will change to " Manual input".
7. CAN analyzer ( hacker )
There may be a situation when a car arrives, but you don’t find it on the list. In such a situation you will need CAN analyzer with which you can find out CAN - parcel. You can use CAN analyzer of our production, for convenience, made in OBD - II housing.
.
Appearance of the program CANanalyzer
After you find out CAN – a parcel, you can manually record it in the rewind (this is written in the section 6. Manual input CAN- parcels) or send data to us and we will add your data to the program.
8 . Rewinding operating time limitation
The winder has a function for limiting operating time. This function can be used to set the winding operation limit.
To create a limit, you must do the following:
1. Calculate the winding speed. To do this, note how much the odometer readings increase in 1 minute;
2. Multiply the resulting value by 60 and get the winding speed;
3. Then divide the kilometer limit you give the client by the speed. For example, the limit is 50,000 km, the speed is 300 km, then the value will be 50,000/300 = 167 hours;
4. Check the “Limit” checkbox and enter the number of hours;
5. Click the Record button;
6. After this, the lower window with the inscription “Remaining” will show the time until the winding is blocked
To remove a restriction, simply uncheck the box next to “Restriction”.
In the "What's new..." section you can find out the latest changes that have been made to the program.
list. ru
Speedometer winder CAN+G (for new cars) unlimited
Restrictions:
In CAN mode
Equipment:
Warranty card
Production: Russia
Ford
Mazda
Toyota
Lexus
Nissan
Infiniti
FX-35, FX-45, QX-56, G35.
Audi
Including the new A6 and A8.
Volkswagen(All models from 2003 onwards)
Skoda(All models)
Mercedes
Honda
Opel
Renault
SsangYong.
Chevrolet
Cadillac
Escalade since 2008, Express.
Hyundai
BMW
KIA
Citroen
C5, Jumper, Berlingo since 2012.
Mitsubishi.
Volvo.
XC90, XC70, S80, S70, S60.
Land Rover
Discovery 3.4, Range Rover.
Suzuki
Vitara, Kizashi, SX-4.
Peugeot
Jeep
Grand Cherokee.
Lada
Datsun
On-do 2014
CAN+G speedometer speed generator (for new cars) unlimited.
SPEEDOMETER WINDER. ADVANTAGES OF CAN CONTROLLER
Restrictions:
In CAN mode The unlimited device is designed to work with one brand of car. That is, after 3-60 hours of operation, the device will disable the ability to configure in CAN mode. There are no restrictions for DS-1 and DS-2 modes.
Equipment:
Speedometer rewind CAN+G (UNLIMITED) Multibrand
Warranty card
Production: Russia
Car support in CAN mode:
Ford
Focus 2, Focus 3, Fusion, Fiesta, Transit, Tourneo, Maveric, C-Max, S-Max, Mondeo, Galaxy, Scorpio, Escape since 2007, Explorer, Ranger.
Mazda
Mazda 2, Mazda 3, Mazda 6, CX-7.
Toyota
HighLander since 2008, Avensis since 2009, Auris since 2006, Camry since 2007, Tundra, Corolla since 2006, Land Cruiser 200, Prado 150 since 2009, Rav4 since 2006, Verso.
Lexus
LX570, RX350 since 2010, LS460 since 2007 and all others after 2012.
Nissan
Teana, Murano, Qashqai, X-Trail, Primera since 2005, Navara, Pathfinder since 2007, Patrol since 2010.
Infiniti
FX-35, FX-45, QX-56, G35.
Audi(All models from 2003 onwards)
Audi A4, A6, A8, Q5, Q7, AllRoad.
Including the new A6 and A8.
Volkswagen(All models from 2003 onwards)
Passat B6, B7, CC, Polo, Golf V, Jetta, Caddy, T5, Touareg, Caravelle, Multivan, Crafter, Tiguan, Amarok.
Skoda(All models)
Octavia, Super B, Yeti, Rapid.
Mercedes(All models from 2005 onwards)
Body types 112, 164, 204, 211, 220, 221, 222, 251, Vito, Viano, Sprinter, ML, GL since 2005.
Honda
Honda Civic since 2008, CRV since 2008, Pilot, Accord.
Opel
Astra since 2010, Antara, Insignia, Zafirta, Astra, Vectra.
Renault
Scenic-2, Megan-2, Megan-3, Fluence, Master, Kangoo, Latitude, (Logan since 2014).
SsangYong.
Rexton-2 since 2007, Kairon, Actyon, Chairman.
Chevrolet
Captiva, Cruze, Tahoe, Aveo since 2012, Orlando, EPICA (automatic transmission) since 2010.
Cadillac
Escalade since 2008, Express.
Hyundai
Sonata since 2011, Solaris (automatic), Elantra (AKPP), I30 (automatic), I35 (automatic), I40 (automatic) IX35, IX55, Santafe, Genesis.
BMW(All models since 2002)
1, 3, 5, 7, X5 series (Body E60, E61, E62, E65, E66, E67, E68, E70)
New BMWs since 2010 in F bodies.
KIA
Sportage from 2011, Sorento from 2012, Cerato, Optima, Quoris, Mohave.
Citroen
C5, Jumper, Berlingo since 2012.
Mitsubishi.
Outlander XL, Outlander III, Lancer X, ASX.
Volvo.
XC90, XC70, S80, S70, S60.
Land Rover
Discovery 3.4, Range Rover.
Suzuki
Vitara, Kizashi, SX-4.
Peugeot
308, 408, 508, 509, 4007, Boxer.
Jeep
Grand Cherokee.
Lada
Granta since 2012, Priora since 2012.
Datsun
On-do 2014
For some Mercedes, VW, Skoda, Audi, Mitsubishi, BMW, Jeep, Peugeot4007 cars, it is necessary to modify the car (put two wires into the diagnostic connector).
*The device allows you to increase mileage on all cars from the support list by switching operating modes, as well as select the winding speed.
**You can return the product within a month if the winding does not suit you or for some reason you are not satisfied.
A short list of vehicle support for Speed Sensor mode:
Price: 2500 rub. CAN ODO+ speedometer winder (no limit)!
CAN ODO+ A winder is a no-limit device that allows you to increase the mileage of a car and can work with one car. In the future, it can be reprogrammed to work with another car.
Available in standard or shortened housing. The winder in a small body takes up little space in your pocket, is lighter and more compact. But the shortened body will not suit owners of cars where the connector is “recessed” into the dashboard.
| Device characteristics CAN ODO+ | |
|---|---|
| Purpose |
CAN rewinding of the electronic speedometer (increasing odometer readings). The device works with both manual and automatic transmissions. |
| Connection type |
Through the OBDII diagnostic connector under the steering column in the vehicle interior, in an extended or shortened housing (depending on the location and depth of the diagnostic connector). As the mileage increases, the data is duplicated in all blocksand service intervals will show the necessary information.. |
| Installation |
The device is completely removable, does not require additional installation, works without interfering with the electrical system of the machine, instructions are included. |
| Speed | Up to 5000 km/h |
| Equipment |
No limit device, warranty card, instructions |
| Guarantee | 2 years |
Extended body. This is an option for cars where the CAN connector is “recessed” into the car panel.
CAN ELECTRONIC SPEEDOMETER CRANKER, WINDER AND CORRECTOR
PRODUCTION AND SALES
Today, an electronic speedometer winder is a modern high-tech device that allows you to independently adjust the mileage on your car’s odometer upward directly from the car’s interior, using the OBD 2 diagnostic connector. The speedometer winder operates via a CAN bus and does not cause errors in the vehicle’s electrical systems.*
· Works with almost all makes and models of foreign cars since 2006.
· The speedometer increases at speeds up to 5000 km/h.
· Payment is made upon receipt by mail.
· Guarantee.
· The speedometer winder does not require special installation.
· Works through the OBD 2 diagnostic connector under the steering column inside the car.
· The device is completely removable, has no additional wires, and works without interfering with the electrical wiring.
· Works both with the engine stopped and with the engine running, which is important in winter.
· The speedometer knob is the size of a matchbox, easily fits in your pocket, and is extremely easy to use.
WHY IS OUR SPEEDOMETER CRANKER AND WHY IS IT BETTER TO BUY IT on the website website
1. Each speedometer winder is tested before sale using special equipment. Absolutely every device is tested and has a guarantee.
2. We offer the current price without overpayment, buy in bulk and get a discount!
3. Payment is made only after checking the functionality; we do not deceive our clients, but only strive to increase their flow.
4. We provide support for a year after purchase. If you have questions about using the speedometer knob, you can always contact our professional consultant.
5. An important aspect is safety: the speedometer winder is completely safe to use, since it does not have its own nutrients and operates from the car’s network.
6. And, perhaps, the most important point: if you have changed your car, then you no longer need to buy a twister, call us and we will set it up for your new car!
